autotests/folding/highlight.asm-avr.fold

0001 ;********************************************************************
0002 ;* LED flasher: LED will flash with a X on/off ratio at PD6
0003 ;*
0004 ;* NOTE: delay depends in the value of X, 1 is fast, 255 is slow
0005 ;*
0006 ;* No copyright ©1998 RES® * FREEWARE *
0007 ;*
0008 ;* NOTE: Connect a low current LED with a 1k resistor in serie from
0009 ;*       Vdd to pin 11 of the MCU. (Or a normal LED with a 330ohm)
0010 ;*
0011 ;* RES® can be reached by email: digitalaudio@mail.com
0012 ;* or visit the website: http://home.wanadoo.nl/electro1/avr
0013 ;*
0014 ;* Version           :1.0
0015 ;* Date              :12/26/98
0016 ;* Author            :Rob's ElectroSoft®
0017 ;* Target MCU        :AT90S1200-12PI@4MHz
0018 ;********************************************************************
0019
0020 .include "1200def.inc"
0021
0022         rjmp    RESET           ;reset handle
0023
0024
0025 ;* Long delay
0026
0027 ;* Register variables
0028
0029         .def  T1      = r1
0030         .def  T2      = r2
0031         .def  temp    = r19
0032
0033 ;* Code
0034
0035 longDelay:
0036         clr   T1                ;T1 used as delay 2nd count
0037         clr   T2                ;T2 used as delay 3d count
0038 delay_1:
0039         dec   T2
0040         brne  delay_1
0041         dec   T1
0042         brne  delay_1
0043         dec   temp              ;temp must be preset as
0044         brne  delay_1           ; delay master count
0045         ret
0046
0047
0048 ;* Resets the data direction register D
0049
0050 ;* Defines
0051
0052         .equ  led   = 6         ;LED at PD6
0053
0054 ;* Code
0055
0056 RESET:
0057         sbi   DDRD, led         ;connect LED to PORTD pin 6
0058
0059
0060 ;* Main program
0061
0062 ;* This part will let the LED go on and off by X
0063
0064 ;* Register variables
0065
0066         .equ  X   =  10         ;enter delaytime X
0067
0068 flash:
0069         sbi   PORTD, led        ;LED on
0070         ldi   temp, X           ;X sec delay
0071         rcall longDelay
0072         cbi   PORTD, led        ;LED off
0073         ldi   temp, X           ;X sec delay
0074         rcall longDelay
0075         rjmp  flash             ;another run
0076
0077 <beginfold id='1'>/*</beginfold id='1'> other
0078 tests <endfold id='1'>*/</endfold id='1'>
0079
0080 .org LARGEBOOTSTART
0081 ; the following sets up RAMPZ:Z to point to a FLASH data object, typically
0082 ; for use with ELPM.
0083 ldi ZL, low (cmdtable * 2)
0084 ldi ZH, high (cmdtable * 2)
0085 .if ((cmdtable * 2) > 65535)
0086 ldi r16, 1
0087 sts RAMPZ, r16
0088 .endif
0089 ; more code follows here
0090 cmdtable: .db "foo", 0x0
0091 .db "Hello\n" // is equivalent to:
0092 .db 'H', 'e', 'l', 'l', 'o', '\\', 'n'
0093 .db '\0', '\177', '\xff'
0094 .db "\nx\rx\ax\bx\fx\tx\vx\\x\0000\xfff\0\1"
0095 0b10_111_2 0xaf3_4 0_12 32_32 $32_3
0096
0097 .macro m
0098 ldi @0, @1
0099 .endm m r16,\ 0
0100
0101 #define TEST \
0102 .IF val \
0103 .DW __TIME__ \
0104 .ELSE \
0105 .DW 1 \
0106 .ENDIF
0107
0108 #defi TEST